The item is currently not in stock. Please log in below and we'll send you a message as soon as the item is in stock. You will be notified only for this item.
Send us an inquiry for your desired item and we will contact you.
Send us an inquiry for your desired item and we will contact you.
The Arduino MKR Vidor 4000 brings Arduino's ease of use to the work with the most powerful reprogrammable chips that exist: FPGAs. With Vidor you can create a board where all pins are PWM signals controlling the speed of motors. You can capture sound in real time and make a sound effect pedal for your guitar. It is possible to create a real-time computer reading sensor information and sending it to a state-of-the-art monitor or capture video and overlay sensor information on the image that will then later be sent over to a screen. You can connect to the Arduino IoT Cloud and control a complex laboratory machine running a large amount of motors. You could even prototype your own processors inside the FPGA and have it to work in parallel to the other microcontroller on the board. Vidor is a device that invites for experimentation, precision, and high speed computation. See what Massimo Banzi, Arduino Co-founder, has to say about this board in the following video. The main chip on the board is the Intel® Cyclone® 10CL016; it contains 16K logic elements, 504 KB of embedded RAM, and 56 18x18 bit HW multipliers for high-speed DSP operations. Each pin can toggle at over 150 MHz and can be configured for functions such as UARTs, (Q)SPI, high resolution/high frequency PWM, quadrature encoder, I2C, I2S, Sigma Delta DAC, etc.
Tehnical specifications
The Arduino MKR Vidor 4000 is based on the SAMD21 microcontroller and Intel® Cyclone® 10CL016.
FPGA Block
FPGA | Intel® Cyclone® 10CL016 (datasheet) |
PCI | Mini PCI Express port with programmable pins |
Camera Connector | MIPI camera connector |
Circuit Operating Voltage | 3.3V |
Digital I/O Pins | 22 headers + 25 Mini PCI Express |
PWM Pins | All Pins |
UART | Up to 7 (depends on FPGA configuration) |
SPI | Up to 7 (depends on FPGA configuration) |
I2C | Up to 7 (depends on FPGA configuration) |
Analog Input Pins | n/a |
Analog Output Pins | n/a |
External Interrupts | n/a |
DC Current per I/O Pin | 4 or 8 mA |
Flash Memory | 2 MB |
SDRAM | 8 MB |
EEPROM | n/a |
Clock Speed | 48 MHz - up to 200 MHz |
Video Output | Micro HDMI |
Microcontroller Block
Microcontroller | SAMD21 Cortex®-M0+ 32bit low power ARM MCU (datasheet) |
Radio module | u-blox NINA-W102 (datasheet) |
Board Power Supply (USB/VIN) | 5V |
Secure Element | ATECC508 (datasheet) |
Supported Battery | Li-Po Single Cell, 3.7V, 1024mAh Minimum |
Circuit Operating Voltage | 3.3V |
Digital I/O Pins | 8 |
PWM Pins | 13 (0 .. 8, 10, 12, 18 / A3, 19 / A4) |
UART | 1 |
SPI | 1 |
I2C | 1 |
Analog Input Pins | 7 (ADC 8/10/12 bit) |
Analog Output Pins | 1 (DAC 10 bit) |
External Interrupts | 10 (0, 1, 4, 5, 6, 7, 8, 9, 16 / A1, 17 / A2) |
DC Current per I/O Pin | 7 mA |
CPU Flash Memory | 256 KB (internal) |
SRAM | 32 KB |
EEPROM | no |
Clock Speed | 32.768 kHz (RTC), 48 MHz |
LED_BUILTIN | 6 |
USB | Full-Speed USB Device and embedded Host |
LED_BUILTIN | 6 |
Mechanical Aspects
Length | 83 mm |
Width | 25 mm |
Weight | 43.5 gr. |
More information