Filtri

Last viewed items

2.8 TFT TOUCH SHIELD FOR ARDUINO W - CAPACITIVE TOUCH, ADAFRUIT 1947

  • Stock YES, 164 pcs. at the supplier
  • Delivery 7 days
  • Brand: ADAFRUIT
  • ID number: 947/38
61,20 €

 

DESCRIPTION

 

Add some sizzle to your Arduino project with a beautiful large touchscreen display shield with built in microSD card connection and a capacitive touchscreen. This TFT display is big (2.8" diagonal) bright (4 white-LED backlight) and colorful (18-bit 262,000 different shades)! 240x320 pixels with individual pixel control. It has way more resolution than a black and white 128x64 display. As a bonus, this display has a capacitive touchscreen attached to it already, so you can detect finger presses anywhere on the screen.

 

This shield is the capacitive version as opposed to the resistive touchscreen adafruit also sell. This touchscreen doesn't require pressing down on the screen with a stylus, and has a nice glossy glass cover. It is a single-touch display.

 

This shield uses SPI for the display and SD card and is easier to use with UNO, Mega & Leonardo Arduino's. The capacitive touchscreen controller uses I2C but you can share the I2C bus with other I2C devices.

 

The shield is fully assembled, tested and ready to go. No wiring, no soldering! Simply plug it in and load up our library - you'll have it running in under 10 minutes! Works best with any classic Arduino (UNO/Duemilanove/Diecimila). Solder three jumpers and you can use it at full speed on a Leonardo or Mega as well.

 

This display shield has a controller built into it with RAM buffering, so that almost no work is done by the microcontroller. This shield needs fewer pins than our v1 shield, so you can connect more sensors, buttons and LEDs: 5 SPI pins for the display, 2 shared I2C pins for the touchscreen controller and another pin for uSD card if you want to read images off of it.

 

Of course, adafruit wouldn't just leave you with a datasheet and a "good luck!" - adafruitve written a full open source graphics library that can draw pixels, lines, rectangles, circles and text. Adafruit also have a touch screen library that detects x & y location and example code to demonstrate all of it. The code is written for Arduino but can be easily ported to your favorite microcontroller!

 

 

 

 

TECHNICAL DETAILS

 

2.8" diagonal color touchscreen TFT

- 240x320 resolution, 18-bit (262,000) color - our library uses 16 bit color mode

ILI9341 (datasheet) controller with built in video RAM buffer

FT2606 touch screen controller

- High speed SPI display with digital I2C touchscreen driver

- The display uses digital pins 13-9. Touchscreen controller requires I2C pins SDA and SCL. microSD pin requires digital #4. That means you can use digital pins 2, 3, 5, 6, 7, 8 and analog 0-5. Pin 4 is available if not using the microSD

- Works with any classic Arduino '328. Solder closed three jumpers to use the ICSP header for use with Leonardo or Mega

- Onboard 3.3V @ 300mA LDO regulator, current draw depends on usage but is about 100mA for the display and touchscreen

- 4 white LED backlight. On by default but you can connect the transistor to a digital pin for backlight control

- Single-touch capacitive touch bonded on top

 

Specifikacije

Glavno

Processor
Broadcom BCM2837B0, Cortex-A53 64-bit SoC @ 1.4 GHz
Memory
512MB LPDDR2 SDRAM
Connectivity
2.4 GHz and 5 GHz IEE 802.11.b/g/n/ac wireless LAN, Bluetooth 4.2/BLE
Access
Extended 40-pin GPIO header
Video & sound:
1 × full size HDMI

Dimenzije

Dolžina
99 mm
Širina
207 mm
Višina
208 mm
Opozorilo! Vsebina lahko vsebuje napake.